IntrisingTM S2000 is a high performance L2+ Ethernet switch w/ 8 PoE 802.3af/at per port 30W which provides L2+ wire speed and management functions for network deployment. In the redundancy, It delivers ITU G.8032 ring recovery less than 50ms, further less than 20ms in the enhance mode. It can help optimization network traffic by comprehensive QoS. Security functions including L2/L3 ingress and egress ACL, port based DHCP server, MAC based DHCP server, also include option 82/66 for DHCP relay. In order optimization AV traffic, it provide Intelligent Auto AV QoS, IGMP v1/v2/v3/ and router port support, which are important features required in AV network. The network discovery support LLDP and CDP(Cisco Discovery Protocol) that help scan and show whole network topology.
And provided different amount of modular ports for different requirement as below:
Compliant with 802.3af/at standard, the S2000 is able to feed each PoE port up to 30 Watt, 720W totally. Also supports advanced PoE management functions, such as PD detection, scheduling and health tracking. PoE detection can detect if the connected PD status such as enabled/disabled, voltage, current, watt and temperature; scheduling is to allow pre-set power feeding schedule upon routine time table; health tracking can detect PD is alive or not, if PD is dead, will restart it.
S2000 support 802.1p CoS(Class of service) QoS by VLAN and DiffServ that greatly enhance the bandwidth management in a network.
IGMPv1/v2/v3 is a importment feature in the AV network. It bring a lot of benefit such as management multicast traffic, save switch bandwidth.
ITU G.8032 ring which can be self-healed in less than 20ms at 250 switches for single ring topology protection. It also supports various ring topologies that include double ring, multi-chain, basic ring and multiple-VLAN ring. It supports MSTP with up to 8 MSTI that allows each spanning tree for each VLAN for redundant links and backward compatible STP and RSTP.
Port based DHCP server can assign dedicated IP address by by port, MAC based DHCP server can assign dedicated IP address by by client’s MAC Address. Option 82 can assign IP address by port for multiple switches with single DHCP option 82 server.
In case of event, S2000 have many useful log for network trouble shutting. Once out of the situation S200 also support send SMS, e-mail, SNMP trap or syslog to the manager immediately.
S2000 chassis and modules are designed for easy maintenance and installation. It also supports dual AC input power 100V to 240V input to increase the network reliability.
S2000 is a reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. It is the best solution for Automation, transportation, surveillance, Wireless backhaul, semiconductor factory applications. S2000 can be used in extreme environments with an operating temperature range of -20°C to 60°C.
|Standards||IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Ethernet
IEEE 802.3ab 1000Base-T Ethernet
IEEE 802.3z Gigabit Fiber
IEEE 802.3ae 10G Ethernet over Fiber
IEEE 802.3an 10G Copper
IEEE 802.3x Flow Control Capability
ANSI/IEEE 802.3 Auto-negotiation
IEEE 802.1Q VLAN
IEEE 802.1p Class of Service
IEEE 802.1X Access Control
IEEE 802.1D Spanning Tree
IEEE 802.1w Rapid Spanning Tree
IEEE 802.1s Multiple Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
IEEE 802.1x User Authentication (Radius)
IEEE 1588 Precision Time Protocol v2
IEEE 802.3 at/af PoE
|MAC Address||16K MAC address table|
|Connectors||Max 16 10/100/1000T RJ-45 with auto MDI/MDI-X function
Max 16 100M Mini-GBIC : SFP sockets
Max 28 1000M Mini-GBIC : SFP sockets
Max 4 10G Mini-GBIC : SFP + sockets
RS-232 console(Female DB-9) x1
USB x 1 for upload/download config file
DIDO : 1 x 6 pin terminal block
|DI/DO||2 Digital Input (DI) : Level 0: -30~2V / Level 1: 10~30V Max input current:8mA
2 Digital Output(DO): Open collector to 40 VDC, 200mA
|PoE Budget||720W for 54V DC input
Note: 54V input is recommended for 802.3at 30W application
|PoE pin assignment||RJ-45 port # 1~#16 support IEEE 802.3at/afPositive (VCC+): RJ-45 pin 1,2Negative (VCC-): RJ-45 pin 3,6|
|Management||SNMP v1/v2c/v3, WEB/SSH/Telnet/CLI|
|SNMP MIB||RFC 1215 Traps MIB*,
RFC 1213 MIB II
RFC 1158 MIB II
RFC 1157 SNMP MIB,
RFC 1493 Bridge MIB*
RFC 1573 IF MIB
RFC 2674 VLAN MIB*,
Partial RFC 1757 RMON,
RFC 2674 Q-Bridge MIB*; Bridge MIB,
|ITU G.8032||Support ITU G.8032 v2/2012 for Ring protection in less than 50ms for self-healed recovery for single ring topology. Supports various ring topologies that include double ring, multi-chain, basic ring and multiple-VLAN ring|
|PoE Management||PoE detection, scheduling, health checking. Per port status include on/off, voltage, current, watts and temperature|
|Port Trunk with LACP||LACP port trunk up to 8 groups|
|Discovery Protocol||LLDP and CDP(Cisco Discovery Protocol)|
|Environmental Monitoring||System input voltage, current, power consumption ambient temperature|
|VLAN||Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID(Up to 4K, VLAN ID can be assigned from 1 to 4094)
GVRP, QinQ**, QoS QinQ**, Protocol based VLAN** ; IPv4/IPv6 Subnet based VLAN
|Spanning Tree||IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree 8/16* MSTI
|Quality of Service||Determined by port, Tag and IPv4 Type of service, IPv4 Differentiated Services Code Points - DSCP|
|Class of Service||IEEE802.1p class of service, per port and provides 8 priority queues|
|QoS by VLAN**||Tagged QoS by VLAN** for all devices in the network|
|IP Security||Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder|
|Login Security||Supports IEEE802.1X Authentication with RADIUS and TACACS+|
|Port Mirror||Ingress, Egress or both direction per port|
|Network Security||802.1X access control for port based and MAC based authentication/static MAC-Port binding
Ingress/Egress L2/L3 ACL
HTTPS for secure access to the web interface
SSH for secure shell to command line interface
|IGMP||Support IGMP snooping v1/v2/v3; Supports IGMP static route; 1024 multicast groups; IGMP router port ; IGMP query; GMRP|
|Bandwidth Control||Support ingress rate limit and egress rate limit/shaping.
In the ingress direction, packet type(Broadcast/Multicast/Flooded Unicast packet) combination rules are allowed.
|Flow Control||Supports Flow Control for Full-duplex and Back Pressure for Half-duplex|
|System Log||Supports System log record to remote server|
|E-Mail/SMS||Supports SMTP Server or cloud server to send event alert. Maximum 8 e-mail accounts for receiving event alert.
Also can send event alert via SMS.
|Relay Alarm||Provides one relay output.
Alarm Relay current carry ability is 1A @ DC24V
|SNMP Trap||SNMP trap v1/v2c/v3|
|DHCP||Provide DHCP v4/v6** Client/Server/Relay that support addition option 82/66
MAC based can assign IP address by specific host
Port based can assign IP address by specific port
|DNS||Provide DNS client feature and support primary and secondary DNS server|
|SNTP||Supports SNTP to synchronize system clock via Internet|
|Firmware Update||Supports HTTP/HTTPs/TFTP/SFTP** firmware upgrade. TFTP backup and restore|
|Configuration import and export||Supports text configuration file for system quick installation.
Support factory reset button to restore all settings back to factory default.
Support USB storage backup and restore config file.
|Power indicator||Power 1 (Green)
Power 2 (Green)
|10/100/1000/10G Base indicator||Orange: 10Gbps speed
Green : 1G/100M/10Mbps
|PoE LEDs||On (Green)|
|R.M LED||R.M. (Green)|
|Dimension||Metal case. IP-30,440mm(W)x325mm(D)x44mm(H)|
|Operating Humidity||5% ~ 95% (Non-condensing)|
|Operating Temperature||-20°C~60°C / -4°F~140°F
-40°C~75°C / -40°F~167°F
|Storage Temperature||-40°C~85°C / -40°F~185°F|
|EMI||FCC Class A|
|EMS||CE EN55032 Class A, CE EN55024,
CE EN61000-4-2, CE EN61000-4-3,
CE EN61000-4-4, CE EN61000-4-5 Ed.3,
CE EN61000-4-6, CE EN61000-4-8,
CE EN61000-4-11, CE EN50121-4,
|Stability||IEC60068-2-32 (Free fall)